Ewon Technical Forum - No data to push??

Hello

I am commissioning a Flexy 205 to push data to Mindsphere. I have done this several times before, but this time, i get the message in the log "No data to push".
I have historical data logging enabled (as well as realtime), I can see the history in the Flexy, the topic selected is correct, the group is correct.
Firmware 14.6.

(05-10-2022, 09:23 AM)alo_dafo Wrote: [ -> ]Hello

I am commissioning a Flexy 205 to push data to Mindsphere. I have done this several times before, but this time, i get the message in the log "No data to push".
I have historical data logging enabled (as well as realtime), I can see the history in the Flexy, the topic selected is correct, the group is correct.
Firmware 14.6.

Downgraded (recovery) to firmware 14.5s1 and then everything works fine.

(05-10-2022, 09:23 AM)alo_dafo Wrote: [ -> ]Hello

I am commissioning a Flexy 205 to push data to Mindsphere. I have done this several times before, but this time, i get the message in the log "No data to push".
I have historical data logging enabled (as well as realtime), I can see the history in the Flexy, the topic selected is correct, the group is correct.
Firmware 14.6.

(05-10-2022, 09:23 AM)alo_dafo Wrote: [ -> ]Hello

I am commissioning a Flexy 205 to push data to Mindsphere. I have done this several times before, but this time, i get the message in the log "No data to push".
I have historical data logging enabled (as well as realtime), I can see the history in the Flexy, the topic selected is correct, the group is correct.
Firmware 14.6.

Downgraded (recovery) to firmware 14.5s1 and then everything works fine.

I am using an template, var_lst file, so I do not have to declare all tags every time. Perhaps the var_csv file has changed? Or some parameters have been added to the tags that I am missing in my files?
As I wrote, it works with 14.5s1 firmware.

Hi,

This sounds weird as I know some customers using 14.6. This firmware also brings some improvement on the Mindsphere connector.

I have just done a little test and it is working fine on my side :
[attachment=1485]
[attachment=1487]
[attachment=1486]

I think you should open a support ticket so that you can share your Ewon backup and we will investigate.

(06-10-2022, 10:36 AM)simon Wrote: [ -> ]Hi,

This sounds weird as I know some customers using 14.6. This firmware also brings some improvement on the Mindsphere connector.

I have just done a little test and it is working fine on my side :

I think you should open a support ticket so that you can share your Ewon backup and we will investigate.

I will see if I can replicate the problem. I know you made improvements in the connector as I was part of that discussion.

I upgraded the firmware once more to 14.6, but didn't reset the config. And it still works after the upgrade.

Has anything changed in the tag definitions between 14.5s1 and 14.6s0 ??

The first time I uploaded my var_lst file via FTP to the 14.6, then it didn't work.
Then did recovery to 14.5s1 and uploaded the file again, then it worked.
Now upgraded to 14.6 with maintained configuration, and it works.

Oh yes, Daniel :-) Sorry I did not figure out it was you :-)

No change in the Tag definition as far as I know Sad

It sounds tags were somehow not taken in account by the connector... Never seen such a thing

Simon

(06-10-2022, 01:06 PM)simon Wrote: [ -> ]Oh yes, Daniel :-) Sorry I did not figure out it was you :-)

No change in the Tag definition as far as I know
It sounds tags were somehow not taken in account by the connector... Never seen such a thing

Simon

If it occurs again I will create a support-backup and raise a support case.

Ok very good idea ! Smile